神马文学网新手必备的资料
来源：百度文库 编辑：神马文学网 时间：2024/04/27 16:47:57
1 新手必备的资料 新手必须保存的资料 EP45-UD3系+E8200超4G的BIOS设置
******************************
MB Intelligent Tweaker(M.I.T.)
******************************
Robust Graphics Booster ..............: [A]
CPU Clock Ratio ......................: [8X]
x Fine CPU Clock Ratio................: +0.0
CPU Frequency ........................: 4.096GHz( 512X8)
********** Clock Chip Control ********
>>>>> Standard Clock Control
CPU Host Clock Control................: [Enabled]
x CPU Host Frequency(Mhz).............: [512]
PCI Express Frequency(Mhz)............: [100]
C.I.A.2...............................: [Disabled]
>>>>> Advanced Clock Control..........: [Press Enter]
CPU Clock Drive.......................: [800mV]
PCI Express Clock Drive...............: [900mV]
CPU Clock Skew........................: [ 0ps]
MCH Clock Skew........................: [ 0ps]
******** DRAM Performance Control ********
Performance Enhance...................: [Standard]
Extreme Memory Profile(X.M.P.)........: [Disabled]
(G)MCH Frequency Latch................: [Auto]
System Memory Multiplier (SPD)........: [2.00D]
Memory Frequency(Mhz).....800.........: 1024
DRAM Timing Selectable (SPD)..........: [Manual]
>>>>> Standard Timing Control
x CAS Latency Time................5...: [ 5]
x tRCD ...........................5...: [ 5]
x tRP.............................5...: [ 5]
x tRAS...........................18...: [15]
>>>>> Advanced Timing Control.........: [Press Enter]
x tRRD............................3...: [ 3]
x tWTR............................3...: [ 3 (11 in Windows)]
x tWR.............................6...: [ 5 (14 in Windows)]
x tRFC...........................52...: [54]
x tRTP............................3...: [ 1 (4 in Windows)]
x Command Rate (CMD) .............0...: [ 2]
>>>>> Channel A Timing Settings.......: [Press Enter]
x Static tRead Value.............10...: [11]
x tRD Phase0 Adjustment...........0...: Auto
x tRD Phase1 Adjustment...........0...: Auto
x tRD Phase2 Adjustment ..........0...: Auto
x tRD Phase3 Adjustment...........0...: Auto
作者：221.131.8.* 2009-6-13 21:14 回复此发言
2 新手必备的资料
x Trd2rd(Different Rank)..........6...: Auto
x Twr2wr(Different Rank)..........6...: Auto
x Twr2rd(Different Rank)..........5...: Auto
x Trd2wr(Same/Diff Rank)..........8...: Auto
x DIMM1 Clock Skew Control (ps).......: Auto
x DIMM2 Clock Skew Control (ps).......: Auto
x DDR Write Training..................: Auto
>>>>> Channel A Driving Settings......: [Press Enter]
x Driving Strength Profile............: [1066MHz]
x Data Driving Pull-Up Level..........: Auto
x Cmd Driving Pull-Up level...........: Auto
x Ctrl Driving Pull-Up Level..........: Auto
x Clk Driving Pull-Up Level...........: Auto
x Data Driving Pull-Down Level........: Auto
x Cmd Driving Pull-Down level.........: Auto
x Ctrl Driving Pull-Down Level........: Auto
x Clk Driving Pull-Down Level.........: Auto
>>>>> Channel B Timing Settings.......: [Press Enter]
x Static tRead Value.............10...: [11]
x tRD Phase0 Adjustment...........0...: Auto
x tRD Phase1 Adjustment...........0...: Auto
x tRD Phase2 Adjustment ..........0...: Auto
x tRD Phase3 Adjustment...........0...: Auto
x Trd2rd(Different Rank)..........6...: Auto
x Twr2wr(Different Rank)..........6...: Auto
x Twr2rd(Different Rank)..........5...: Auto
x Trd2wr(Same/Diff Rank)..........8...: Auto
x DIMM1 Clock Skew Control (ps).......: Auto
x DIMM2 Clock Skew Control (ps).......: Auto
x DDR Write Training..................: Auto
>>>>> Channel B Driving Settings......: [Press Enter]
x Driving Strength Profile............: [1066MHz]
x Data Driving Pull-Up Level..........: Auto
x Cmd Driving Pull-Up level...........: Auto
x Ctrl Driving Pull-Up Level..........: Auto
x Clk Driving Pull-Up Level...........: Auto
x Data Driving Pull-Down Level........: Auto
x Cmd Driving Pull-Down level.........: Auto
x Ctrl Driving Pull-Down Level........: Auto
x Clk Driving Pull-Down Level.........: Auto
****** Motherboard Voltage Control ******
3 新手必备的资料
Voltage Types..........Normal...........Current
-----------------------------------------------
>>> CPU
Load-Line Calibration.................: [Enabled]
CPU Vcore..............1.27500V.......: [1.4V (1.38V in Windows)]
CPU Termination........1.200V.........: [1.300V]
CPU PLL................1.500V.........: [1.65V]
CPU Reference..........0.760V.........: [.76 (.7 when VTT is 1.2)]
>>> MCH/ICH
MCH Core...............1.100V.........: [1.380V]
MCH Reference..........0.760V.........: [.72]
MCH/DRAM Reference.....0.900V.........: [1.05]
ICH I/O................1.500V.........: [1.5V]
ICH Core...............1.100V.........: [1.1V]
>>> DRAM
DRAM Voltage...........1.800V.........: [2.12V (2.11 in Windows)]
DRAM Termination.......0.900V.........: [1.05]
Channel A Reference....0.900V.........: [1.05]
Channel B Reference....0.900V.........: [1.05]
******** Advanced BIOS Features ********
No-Execute Memory Protect.............: [Enabled]
CPU Enhanced Halt (C1E)...............: [Disabled]
C2/C2E State Support..................: [Disabled]
x C4/C4E State Support................: Disabled
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.....................: [Disabled]
Virtualization Technology.............: [Disabled]
Delay For HDD (Secs)..................: [ 0]
Full Screen LOGO Show.................: [Disabled]
Init Display First....................: [PEG]
******** Integrated Peripherals ********
USB Keyboard Function.................: [Disabled]
USB Mouse Function....................: [Disabled]
USB Storage Function..................: [Disabled]
******************************
MB Intelligent Tweaker(M.I.T.)
******************************
Robust Graphics Booster ..............: [A]
CPU Clock Ratio ......................: [8X]
x Fine CPU Clock Ratio................: +0.0
CPU Frequency ........................: 4.096GHz( 512X8)
********** Clock Chip Control ********
>>>>> Standard Clock Control
CPU Host Clock Control................: [Enabled]
x CPU Host Frequency(Mhz).............: [512]
PCI Express Frequency(Mhz)............: [100]
C.I.A.2...............................: [Disabled]
>>>>> Advanced Clock Control..........: [Press Enter]
CPU Clock Drive.......................: [800mV]
PCI Express Clock Drive...............: [900mV]
CPU Clock Skew........................: [ 0ps]
MCH Clock Skew........................: [ 0ps]
******** DRAM Performance Control ********
Performance Enhance...................: [Standard]
Extreme Memory Profile(X.M.P.)........: [Disabled]
(G)MCH Frequency Latch................: [Auto]
System Memory Multiplier (SPD)........: [2.00D]
Memory Frequency(Mhz).....800.........: 1024
DRAM Timing Selectable (SPD)..........: [Manual]
>>>>> Standard Timing Control
x CAS Latency Time................5...: [ 5]
x tRCD ...........................5...: [ 5]
x tRP.............................5...: [ 5]
x tRAS...........................18...: [15]
>>>>> Advanced Timing Control.........: [Press Enter]
x tRRD............................3...: [ 3]
x tWTR............................3...: [ 3 (11 in Windows)]
x tWR.............................6...: [ 5 (14 in Windows)]
x tRFC...........................52...: [54]
x tRTP............................3...: [ 1 (4 in Windows)]
x Command Rate (CMD) .............0...: [ 2]
>>>>> Channel A Timing Settings.......: [Press Enter]
x Static tRead Value.............10...: [11]
x tRD Phase0 Adjustment...........0...: Auto
x tRD Phase1 Adjustment...........0...: Auto
x tRD Phase2 Adjustment ..........0...: Auto
x tRD Phase3 Adjustment...........0...: Auto
2 新手必备的资料
x Trd2rd(Different Rank)..........6...: Auto
x Twr2wr(Different Rank)..........6...: Auto
x Twr2rd(Different Rank)..........5...: Auto
x Trd2wr(Same/Diff Rank)..........8...: Auto
x DIMM1 Clock Skew Control (ps).......: Auto
x DIMM2 Clock Skew Control (ps).......: Auto
x DDR Write Training..................: Auto
>>>>> Channel A Driving Settings......: [Press Enter]
x Driving Strength Profile............: [1066MHz]
x Data Driving Pull-Up Level..........: Auto
x Cmd Driving Pull-Up level...........: Auto
x Ctrl Driving Pull-Up Level..........: Auto
x Clk Driving Pull-Up Level...........: Auto
x Data Driving Pull-Down Level........: Auto
x Cmd Driving Pull-Down level.........: Auto
x Ctrl Driving Pull-Down Level........: Auto
x Clk Driving Pull-Down Level.........: Auto
>>>>> Channel B Timing Settings.......: [Press Enter]
x Static tRead Value.............10...: [11]
x tRD Phase0 Adjustment...........0...: Auto
x tRD Phase1 Adjustment...........0...: Auto
x tRD Phase2 Adjustment ..........0...: Auto
x tRD Phase3 Adjustment...........0...: Auto
x Trd2rd(Different Rank)..........6...: Auto
x Twr2wr(Different Rank)..........6...: Auto
x Twr2rd(Different Rank)..........5...: Auto
x Trd2wr(Same/Diff Rank)..........8...: Auto
x DIMM1 Clock Skew Control (ps).......: Auto
x DIMM2 Clock Skew Control (ps).......: Auto
x DDR Write Training..................: Auto
>>>>> Channel B Driving Settings......: [Press Enter]
x Driving Strength Profile............: [1066MHz]
x Data Driving Pull-Up Level..........: Auto
x Cmd Driving Pull-Up level...........: Auto
x Ctrl Driving Pull-Up Level..........: Auto
x Clk Driving Pull-Up Level...........: Auto
x Data Driving Pull-Down Level........: Auto
x Cmd Driving Pull-Down level.........: Auto
x Ctrl Driving Pull-Down Level........: Auto
x Clk Driving Pull-Down Level.........: Auto
****** Motherboard Voltage Control ******
3 新手必备的资料
Voltage Types..........Normal...........Current
-----------------------------------------------
>>> CPU
Load-Line Calibration.................: [Enabled]
CPU Vcore..............1.27500V.......: [1.4V (1.38V in Windows)]
CPU Termination........1.200V.........: [1.300V]
CPU PLL................1.500V.........: [1.65V]
CPU Reference..........0.760V.........: [.76 (.7 when VTT is 1.2)]
>>> MCH/ICH
MCH Core...............1.100V.........: [1.380V]
MCH Reference..........0.760V.........: [.72]
MCH/DRAM Reference.....0.900V.........: [1.05]
ICH I/O................1.500V.........: [1.5V]
ICH Core...............1.100V.........: [1.1V]
>>> DRAM
DRAM Voltage...........1.800V.........: [2.12V (2.11 in Windows)]
DRAM Termination.......0.900V.........: [1.05]
Channel A Reference....0.900V.........: [1.05]
Channel B Reference....0.900V.........: [1.05]
******** Advanced BIOS Features ********
No-Execute Memory Protect.............: [Enabled]
CPU Enhanced Halt (C1E)...............: [Disabled]
C2/C2E State Support..................: [Disabled]
x C4/C4E State Support................: Disabled
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.....................: [Disabled]
Virtualization Technology.............: [Disabled]
Delay For HDD (Secs)..................: [ 0]
Full Screen LOGO Show.................: [Disabled]
Init Display First....................: [PEG]
******** Integrated Peripherals ********
USB Keyboard Function.................: [Disabled]
USB Mouse Function....................: [Disabled]
USB Storage Function..................: [Disabled]
新手必备的资料
批处理(BAT)新手资料
【玩转智能手机全部必备资料（新手级与高手级都适用)(诺基亚 5800XM-诺基亚手机...
新手上路必备安全知识
最新外贸流程图 新手必备！
新手找国外客户必备！
电脑高手必备资料大全
公务员考试必备资料
影楼公司必备资料
【穿越必备常识】关于古代钱币的资料集
新手如何开车【资料教程】
公务员考试、必备资料下载
新手找国外客户必备！精品！
股市知识点大全【新手必备宝典】
新手学开车系列【教你如何开车】 - 【资料教程】 -的 QQQX论坛
新手司机比看-----内部资料
新手学开车系列 - 【资料教程
每个家庭必备最好的教育讲座资料《幸福人生讲座》
用户必备资料 103个Windows XP运行命令 - 电脑爱好者学习交流的乐园 - 睢宁...
网络资料之学生论文、考试必备
公务员考试必备资料下载1
玩转智能手机全部必备资料
快速租赁网业务员必备资料
中考备战初中化学第一轮复习必备资料