mujuyingyu

一、浇口(入水)：gate
        浇口进入位置：gate location
        浇口形式：gate type
        大水口(2板模)：edge gate, side gate
        细水口(3板模)：pin-point gate
        浇口大小：gate size
        转开关流道：switching runner/gate
        唧嘴直径：sprue diameter
二、流道：runner
        热流道：hot runner，hot manifold
        温控箱：temperature controller
        热嘴冷流道：hot sprue/cold runner
        唧嘴直流：direct sprue gate
        圆形流道：round(full/half) runner
        模流道电脑分析：mold flow analysis
        流道平衡：runner balance
        热嘴：hot sprue
        热流道板：hot manifold
        发热管：cartridge heater
        探温针：thermocouples
        插头：connector plug
        插座：connector socket
        密封/封料：seal
三、运水：water line
        喉塞：line plug
        喉管：tube
        塑胶管：plastic tube
        快速接头：jiffy quick connector plug/socket
四、模具零件：mold components
        三板模：3-plate mold
        二板模：2-plate mold
        导柱(边钉/导边)：leader pin/guide pin
        导套(边司)：bushing/guide bushing  
        顶针板：ejector retainer plate
        托板：support plate
        螺丝：screw
        管销(管钉)：dowel pin
        开模槽：ply bar slot
        内模管位锁：core/cavity inter-lock
        顶针：ejector pin
        司筒：ejector sleeve
        司筒针：ejector sleeve pin
        推板：stripper plate
        缩呵：movable core，return core，core puller
        扣机(尼龙拉勾)：nylon latch lock
        斜顶：lifter
        模胚(架)：mold base
        上内模：cavity insert
        下内模：core insert
        行位(滑块)：slide
        镶件：insert
        压座(斜鸡)：wedge，heeled block
        耐磨板/油板：wedge wear plate
        压条：guide way plate  
        模顶(撑头)：support pillar
        唧嘴：sprue bushing
        挡板：stop plate
        定位圈：locating ring
        锁扣：latch
        扣鸡：parting lock set
        推杆：push bar
        栓打螺丝：S.H.S.S.(socket head shoulder screw)
        杯头螺丝：S.H.C.S.(socket head cap screw)
        活动臂：lever arm
        分流锥：sprue separator
        垃圾钉：stop pin
        水隔片：buffle
        弹弓柱：spring rod
        弹弓：die spring
        中托司：ejector guide bush
        中托导套(边)：ejector guide pin
        镶针：insert pin
        波子弹弓：ball catch
        喉塞：pipe plug
        锁模块：lock plate
        行位斜导柱：angle pin
        斜顶杆：angle ejector rod  
        复位键/提前回杆：early return bar
        气阀：valves
五、术语：terms
        承压平面平衡：parting surface support balance
        模排气：parting line venting
        回针碰料位：return pin and cavity interference
        模闭合总厚度：mold base shut height
        顶针碰运水：water line interferes with ejector pin
        料位出上(下)模：part from cavity (core) side
        模胚原身出料位：cavity direct cut on A-plate，core direct cut on B-plate.
        不准用镶件： do not use (core/cavity) insert
        用铍铜做镶件： use beryllium copper insert
        初步(正式)模图设计：preliminary (final) mold design
        反呵：reverse core
        弹弓压缩量：spring compressed length
        强度不够：insufficient rigidity
        均匀冷却：even cooling
        扣前模：sticking
        热膨胀：thermo expansion
        公差：tolerance
        铜电极(铜公)：copper electrode
        石墨电极：graphite electrode
        夹线：weld line
        翘曲：warpage
        缺胶：short shot
        困气：air trap
        毛刺：flash，burr

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 

模具述语
一、入水：gate
进入位：　gate location
水口形式：gate type
大水口：edge gate
细水口： pin-point gate
水口大小：gate size
转水口：　switching runner/gate
唧嘴口径：　sprue diameter
二、流道: runner
热流道：　hot runner,hot manifold
热嘴冷流道: hot sprue/cold runner
唧嘴直流: direct sprue gate
圆形流道：round(full/half runner
流道电脑分析：mold flow analysis
流道平衡:runner balance
热嘴：　hot sprue
热流道板：hot manifold
发热管：cartridge heater
探针: thermocouples
插头：　connector plug
插座： connector socket
密封/封料： seal
三、运水：water line
喉塞：line lpug
喉管：tube
塑胶管：plastic tube
快速接头：jiffy quick connector plug/socker
四、模具零件：　mold components
三板模：3-plate mold
二板模：2-plate mold
边钉/导边：leader pin/guide pin
边司/导套：bushing/guide bushing
中托司：shoulder guide bushing
中托边L：guide pin
顶针板：ejector retainner plate
托板：　support plate
螺丝： screw
管钉：dowel pin
开模槽：ply bar scot
内模管位：core/cavity inter-lock
顶针：　ejector pin
司筒：ejector sleeve
司筒针：ejector pin
推板：stripper plate
缩呵：movable core,return core core puller
扣机（尼龙拉勾）：nylon latch lock
斜顶：lifter
模胚（架）： mold base
上内模：cavity insert
下内模：core insert
行位（滑块）： slide
镶件：insert
压座/斜鸡：wedge
耐磨板/油板：wedge wear plate
压条：plate  
撑头: support pillar
唧嘴： sprue bushing
挡板：stop plate
定位圈：locating ring
锁扣：latch
扣鸡：parting lock set
推杆：push bar
栓打螺丝：S.H.S.B
顶板：eracuretun
活动臂：lever arm
分流锥：spure sperader
水口司:bush
垃圾钉：stop pin
隔片：buffle
弹弓柱：spring rod
弹弓:die spring
中托司：ejector guide bush
中托边：ejector guide pin
镶针：pin
销子：dowel pin
波子弹弓：ball catch
喉塞: pipe plug
锁模块：lock plate
斜顶：angle from pin
斜顶杆：angle ejector rod
尼龙拉勾：parting locks
活动臂：lever arm
复位键、提前回杆：early return bar
气阀：valves
斜导边：angle pin
术语：terms
承压平面平衡：parting surface support balance
模排气：parting line venting
回针碰料位：return pin and cavity interference
模总高超出啤机规格：mold base shut hight
顶针碰运水：water line interferes withejector pin
料位出上/下模：part from cavith (core) side
模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.
不准用镶件： Do not use (core/cavity) insert
用铍铜做镶件： use beryllium copper insert
初步（正式）模图设计：preliinary (final) mold design
反呵：reverse core
弹弓压缩量：spring compressed length
稳定性好：good stability,stable
强度不够：insufficient rigidity
均匀冷却：even cooling
扣模：sticking
热膨胀：thero expansion
公差：tolorance
铜公(电极）：copper electrode

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Surface Appearance 外观

Glossiness/gloss finish 光洁度

Matt finish/matt surface 毛面

Glass fiber rich surface/glass emergence on the surface 玻纤外露

Blooming/surface blooming 表面析出

White patches on surface 表面白斑

Silver marks/silver streak 银纹

Splay mark 水纹

Flow mark 流纹

Weld line 溶结纹

Brittle/brittleness 脆

Bubbles/trapped gas 气泡

Void 孔

Burn marks 烧伤

FR failed 阻燃不合格

Flame rating V-2 阻燃V-2

Poor dispersion 分散不好

FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块

Pellet porous 粒子不密/蜜蜂窝

Low impact/tensile etc 物理性能低

High flow/filler content etc 流动性/填充…过高

Longs/fines/doubles 长粒/碎屑/连粒

Poor cut 粒形不好

Bristle/voids 表面有小气泡/孔

Glass bundles 玻纤结团

Product was rejected due to  产品不能接受因为…

High moisture level 高水分

Warpage/warped 翘曲

Shrinkage/shrink 收缩

Sink marks 缩影

Short shot/short molding 打不满

Distortion 变形

Over dimension 尺寸过大

Under dimension 尺寸过小

Flashing 飞边

Discoloration 变色

Off color 颜色差异

Flow rate 流动率

Viscous 粘

High flow 高流动

Low flow 低流动

Sticky 粘

Mold release 脱模

Antioxidant 抗氧剂

Flame retardant agent 阻燃剂

Heat stabilizer 热稳定剂

Chopped glass fiber 短切玻纤

Roving glass fiber 粗纱/长玻纤

Glass beads 玻璃微珠

Milled fiber 碾磨纤

Molybdenum disulfide/moly/MoS2 二硫化钼

Colorant 着色剂

Pigment 颜料

Dye 染料

Accepted product specification 接受产品规格

Approved our product 认可我们的产品

Re-set spec 重新定标准

Add in extra … 添加多一点…

Reduced … content 减少…含量

Dropped/reduced … by x％ 减少…含量…％

Confirmed color standard 确认颜色标准

Approved color standard 认可颜色标准

Re-confirmed color standard 重新确认颜色标准

Qualified our product 认可我们的产品

Undergoing heat aging test 在做热老化实验

Product is under testing 产品在测试当中

Received first order 接了第一个定单

Expected to finish by … 预计在…完成

Expected order is xMT 预计定单量…吨

Estimated annual/monthly consumption 预计年/月用量

 来源：[http://www.jdzj.com]机电之家·机电行业电子商务平台！