OSPF协议配置指南-
来源:百度文库 编辑:神马文学网 时间:2024/04/27 16:27:35
OSPF协议配置指南
9. 使用身份验证
为了安全的原因,我们可以在相同OSPF区域的路由器上启用身份验证的功能,只有经过身份验证的同一区域的路由器才能互相通告路由信息。
在默认情况下OSPF不使用区域验证。通过两种方法可启用身份验证功能,纯文本身份验证和消息摘要(md5)身份验证。纯文本身份验证传送的身份验证口令为纯文本,它会被网络探测器确定,所以不安全,不建议使用。而消息摘要(md5)身份验证在传输身份验证口令前,要对口令进行加密,所以一般建议使用此种方法进行身份验证。
使用身份验证时,区域内所有的路由器接口必须使用相同的身份验证方法。为起用身份验证,必须在路由器接口配置模式下,为区域的每个路由器接口配置口令。
以下是引用片段: 任务 命令 指定身份验证 area area-id authentication [message-digest] 使用纯文本身份验证 ip ospf authentication-key password 使用消息摘要(md5)身份验证 ip ospf message-digest-key keyid md5 key
以下列举两种验证设置的示例,示例的网络分布及地址分配环境与以上基本配置举例相同,只是在Router1和Router2的区域0上使用了身份验证的功能。:
例1.使用纯文本身份验证
Router1:
以下是引用片段: interface ethernet 0 ip address 192.1.0.129 255.255.255.192 ! interface serial 0 ip address 192.200.10.5 255.255.255.252 ip ospf authentication-key cisco ! router ospf 100 network 192.200.10.4 0.0.0.3 area 0 network 192.1.0.128 0.0.0.63 area 1 area 0 authentication !
Router2:
以下是引用片段: interface ethernet 0 ip address 192.1.0.65 255.255.255.192 ! interface serial 0 ip address 192.200.10.6 255.255.255.252 ip ospf authentication-key cisco ! router ospf 200 network 192.200.10.4 0.0.0.3 area 0 network 192.1.0.64 0.0.0.63 area 2 area 0 authentication !
例2.消息摘要(md5)身份验证:
Router1:
以下是引用片段: interface ethernet 0 ip address 192.1.0.129 255.255.255.192 ! interface serial 0 ip address 192.200.10.5 255.255.255.252 ip ospf message-digest-key 1 md5 cisco ! router ospf 100 network 192.200.10.4 0.0.0.3 area 0 network 192.1.0.128 0.0.0.63 area 1 area 0 authentication message-digest !
Router2:
以下是引用片段: interface ethernet 0 ip address 192.1.0.65 255.255.255.192 ! interface serial 0 ip address 192.200.10.6 255.255.255.252 ip ospf message-digest-key 1 md5 cisco ! router ospf 200 network 192.200.10.4 0.0.0.3 area 0 network 192.1.0.64 0.0.0.63 area 2 area 0 authentication message-digest !
相关调试命令:
以下是引用片段: debug ip ospf adj debug ip ospf events